Amplifier mounting and connections
After routing the power and signal cables to your amplifier, using the techniques described on page 3, you're ready to mount and hook up the amplifier. First, remove a bolt near the planned amp location. Crimp a ring terminal (included with the kit) to the short piece of black ground cable (also in the kit). Scrape away any paint and clean the bolt location thoroughly (improper grounding is the #1 cause of noise problems), and then bolt the terminal tightly to the vehicle's metal chassis. If you can't find a convenient ground screw or bolt, drill a hole for one — be careful not to drill into the gas tank or a gas or brake line).
Accessories Click Here:
http://aawholesaler.com
Friday, March 7, 2008
Thursday, March 6, 2008
Wire routing
All system wiring should be concealed for safety, and to give your installation a nice, finished look. Wires should be secured so that they do not interfere with safe vehicle operation. Depending on the vehicle and the location you choose for your amplifier, the wiring for your system may need to be run under the dash, door scuff plate, pillar trimpanel, or kickpanel. The instructions below address, in general, what panels may need to be removed and how they typically come off. Often, panels can be pried up at edges. Screws and retaining clips might also be present that will require removal (Figure 1). To prevent damage, always use care when removing panels — a panel tool is helpful.
AMP Accessories and more:
http://aawholesaler.com
All system wiring should be concealed for safety, and to give your installation a nice, finished look. Wires should be secured so that they do not interfere with safe vehicle operation. Depending on the vehicle and the location you choose for your amplifier, the wiring for your system may need to be run under the dash, door scuff plate, pillar trimpanel, or kickpanel. The instructions below address, in general, what panels may need to be removed and how they typically come off. Often, panels can be pried up at edges. Screws and retaining clips might also be present that will require removal (Figure 1). To prevent damage, always use care when removing panels — a panel tool is helpful.
AMP Accessories and more:
http://aawholesaler.com
Monday, March 3, 2008
STEP 6.
If your in-dash radio has preamp (RCA) outputs, connect the RCA patch cables (included with most kits) to these outputs, taping them together so they won't come apart. Route the patch cables (again, using wire ties) to the OPPOSITE side of the vehicle from the power cable and blue turn on lead. It's important to separate the patch cables from the power wires to avoid potential noise problems. Now you can partially re-install the radio in the dash (don't push it all the way in, in case you need to fix a problem later).
For AMP Accessories go to:
http://aawholesaler.com
If your in-dash radio has preamp (RCA) outputs, connect the RCA patch cables (included with most kits) to these outputs, taping them together so they won't come apart. Route the patch cables (again, using wire ties) to the OPPOSITE side of the vehicle from the power cable and blue turn on lead. It's important to separate the patch cables from the power wires to avoid potential noise problems. Now you can partially re-install the radio in the dash (don't push it all the way in, in case you need to fix a problem later).
For AMP Accessories go to:
http://aawholesaler.com
Sunday, March 2, 2008
STEP 5.
Remove the radio from the dash to access the turn-on wire (usually a blue wire). The turn-on wire will "tell" your amplifier to turn on whenever the receiver is powered up (usually, whenever the vehicle is turned on).
Strip the insulation off a small section of this wire coming from the radio, wrap the blue turn on lead (included with the amp wiring kit) around it, and solder. Or, use crimp connectors and a crimp tool to connect the blue turn on lead to the wire coming from the radio. Wrap the solder or crimp connection with electrical tape (or use a heat gun to apply heat shrink tubing) to guard against a short. Using wire ties (included with the kit) to secure the wire, route the blue turn on lead behind your dash all the way over to the place where the red power wire comes through the firewall.
Making the signal connections
For AMP wire and more go to:
http://aawholesaler.com
Remove the radio from the dash to access the turn-on wire (usually a blue wire). The turn-on wire will "tell" your amplifier to turn on whenever the receiver is powered up (usually, whenever the vehicle is turned on).
Strip the insulation off a small section of this wire coming from the radio, wrap the blue turn on lead (included with the amp wiring kit) around it, and solder. Or, use crimp connectors and a crimp tool to connect the blue turn on lead to the wire coming from the radio. Wrap the solder or crimp connection with electrical tape (or use a heat gun to apply heat shrink tubing) to guard against a short. Using wire ties (included with the kit) to secure the wire, route the blue turn on lead behind your dash all the way over to the place where the red power wire comes through the firewall.
Making the signal connections
For AMP wire and more go to:
http://aawholesaler.com
Subscribe to:
Posts (Atom)
